UniFi Building Bridge 3.3.0 includes the improvements and bugfix below.

Improvements

• Updated 60GHz radio regulatory requirements for Brazil.
• Improved auto frequency selection for the 60GHz radio.
• Improved system stability.

Bugfixes

• Fixed an issue where IPv6 didn't work when a management VLAN was configured.

Additional information

• Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
• If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

• Added support for Building Bridge Single Units. Learn More
• Requires UniFi Network Application 10.0 or newer.
• iOS: 10.31.4 or newer.
• Android: 10.34.1 or newer.
• Improved auto frequency selection for the 5GHz radio.
• Improved adoption resiliency.
• Improved the LED behavior while in the factory default state.
• Improved connection resiliency when using Network Override.

Bugfixes

• Fixed an issue where the device could report incorrect temperatures.

Additional information

If you encounter any issues with this release, please provide us with some details on your setup and include the following information:

• Previous release version
• UniFi Network application version

UniFi Building Bridge 3.1.7 includes the improvement listed below.

Improvements

• Improved device stability.

Additional information

• Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
• If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

UniFi Building Bridge 3.1.5 includes the improvement and bugfix listed below.

Improvements

• Improved radio failover resiliency.

Bugfixes

• Fixed an issue where DNS Suffix wasn't being applied when configuring a static IP.

Additional information

• Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
• If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

UniFi Building Bridge 3.1.4 includes the improvements and bugfixes listed below.

Improvements

• Added support for the 60 GHz radio in the Philippines.
• Added support for selecting DFS channels for the 5GHz radio.
• Improved auto frequency selection for the 5GHz radio.
• Improved statistics reporting to the Network Application.
• Updated radio regulations for various countries.

Bugfixes

• Fixed the inability to use locate in rare cases.
• Fixed an issue where LACP packets didn't get passed through correctly.

Additional information

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

UniFi Building Bridge 3.1.0 adds 60GHz support for various countries listed under improvements.

Improvements

• Added support for the 60 GHz radio in the following countries:
• Argentina, Chile, Colombia, Egypt, Israel, Kazakhstan, Morocco, Nigeria and Thailand
• Allow passing traffic while devices are unadopted.
• Increased frequency range for the 60 GHz radio in the following countries:
• Belgium, Brazil, Canada, Chechia, Germany, Spain, Finland, France, Great Britain, Ireland, Lithuania, Norway, New Zeland, Poland, Sweden and Singapore

Additional information

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

UniFi Building Bridge 3.0.6 includes the improvements listed below.

Improvements

• Allow selecting UNII-1 frequency range for the 5GHz radio.
• Improved device stability.

Additional information

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

UniFi Building Bridge 3.0.2 includes the improvements and fixes listed below.

Improvements

• Improved connection resiliency.
• Improved CPU usage.
• Improved performance of the 5GHz radio.
• Improved stability and performance of the 60GHz radio.

Bugfixes

• Fixed 60GHz bandwidth setting.
• Fixed channel list for the backup radio (5GHz)
• Fixed unable to pass traffic over 60GHz in rare cases.
• Fixed unable to pass traffic with higher MTU.
• Fixed a rare case where the UBB could become inaccessible.

Additional information

If you encounter any issues with this release, please provide us some details on your setup and include the below information:

• Previous release version
• UniFi Network application version

• Update 60G Mexico regulation.
• Improve topology reporting.
• Improve reconnection after forget.
• Improve alignment tool - higher priority than 60G missing pattern.
• Enhance storing pair data for better devices reliability.

Bugfixes

• Fix LED color/brightness settings.

Additional information

• Instead of using the manual links, you can also subscribe to your desired firmware channel, as described here.

Any and all feedback is welcome, including lettings us know about successful device upgrades. When reporting an issue, please ensure that you include the following information:

• Network Application version.
• Firmware version (previous and current). 
• Device model(s). 

• Improved stability of 60GHz radio communication with the OS.
• Improved 60G link stability for low SNR value.
• Updated 60G radio firmware.
• Updated regulatory for Russia.
• Updated regulatory for Australia.
• Updated regulatory for New Zealand.

Bugfixes

• Fixed issue related to stopping passing data through 60G radio.
• Fix https download for upgrade command.
• Several minor bug fixes.

Release Stage: Stable

New features

• Management VLAN support.

Improvements

• Faster link switching to/from the backup link.
• Quick recovery instead of reboot in case of 60GHz radio stability issues.
• 60GHz station scans and connects ten times faster than before.
• Fast switching between 60GHz channels and channel widths.
• Improved link failover to 5GHz when 60GHz has low capacity or disconnects.
• Improved Alignment tool responsiveness.

Bugfixes

• Alignment tool starts automatically for non-adopted devices.

Additional information

• Devices running 1.0.x-betaX firmware won't automatically upgrade. They will require a Custom Upgrade in the controller, or manual upgrade via shell. Once on 1.0.4 or later they should automatically pick up updates that are pushed to the firmware update service.

Checksum

MD5: 067ac5e349cb3ca1849132e43389211c
SHA256: aa7dc0e211b1648b4423eecd4130ad42a479a2a2e05053e830144f2e55edfa0b

Release Stage: Stable

New features

• Alignment tool

Improvements

• Pre-adoption device accessibility improvement (ARP forwarding)
• Improved LED notification
• Verbose DHCP client logs

Bugfixes

• DHCP renew / lease fix

Additional information

• Devices running 1.0.x-betaX firmware won't automatically upgrade. They will require a Custom Upgrade in the controller, or manual upgrade via shell. Once on 1.0.4 or later they should automatically pick up updates that are pushed to the firmware update service.

Checksum

MD5: 67a82e242a55eb4c23a0256163908477
SHA256: 2bfcb6c611a9e45a59a0ef870fc109f8a133e5d2076c57999246d98a93784ff9